Блокировки дифференциала на все внедорожники
Блокировка дифференциала и главная пара на любой внедорожник!
Пневматические блокировки TJM Pro Locker Пневматические блокировки ARB Air Locker Блокировки Eaton Detroit Truetrac и Detroit Locker Главные пары Nitro gear и усиленные ШРУСы и полуоси Усиленные полуоси и ШРУСы Trail gear Главные пары Yukon gear и блокировки Grizzly Locker Главные пары HF Standard gear и блокировки HF Air Locker
        Магазин:
+7 984 2-200-100
Связаться по WhatsappСвязаться в Telegram     Мастерская:  +7 914 790-98-73
(пусто)
 
Магазин "Blokirovka.ru"
Адреса: 
Магазин во Владивостоке
ВладивостокДнепровская, 25Д  (+7-984-2-200-100)
      E‑mail: info@blokirovka.ru

Типы мостов и какой лучше?

Semi-Floating

The semi-floating axle design secures the wheel directly to the flange face on the outer end of the axle shaft. A single bearing supports the outer end of the shaft inside of the axle tube. The axle shaft has to support the weight on the axle and the propulsion forces from the engine twisting it. The semi-floater is standard on most sport-utilities, half-ton and light-duty 3/4-ton pickups.

Full-Floating

In this design, the wheel is fastened to a separate hub which rotates on two large, opposing, tapered roller bearings secured to a spindle on the outer ends of the axle housing. All of the weight is carried on the hub and two large hub bearings, while the axle shaft goes through the hub and handles only the twisting force from the engine. With more than double the bearing area, and no bending forces acting on the axle shaft, the full-floater is standard in most 3/4-ton HD and 1-ton pickups. It is the design of choice for heavy payloads or trailers, big-block and turbo diesel engines, and very large tires, up to 10,000 GAWR.

Which is Better?

Full-floating setups are a must for 3/4-ton and heavier trucks, and a good idea for 1/2-ton trucks that haul a lot of weight, tow heavy trailers, or see severe 4WD use.

Reverse Cut vs. Standard Cut

Perhaps the single most misunderstood axle term is reverse cut, often mistakenly referred to as reverse rotation. A reverse cut housing is not a standard cut housing turned upside down, it is a specially designed housing. The term "reverse cut" refers to the direction of the spiral cut in the ring gear, which is opposite that of a standard cut ring gear: Contrary to popular belief, it does not run backwards or in reverse. The principle behind a reverse cut is to strengthen the operation of the gear when it is used for a front driving axle application.

Hi-pinion or reverse-cut axles have also become very popular as rear driving axles in short wheelbase vehicles with suspension lifts because the higher pinion improves drive line angles so well.

Standard-cut axles are often used as the front driving axles because of clearance issues, gear ratio availability, cost, or suspension considerations. However comparable reverse-cut axles have the distinct advantage of overall ring and pinion gear strength.

Reverse-cut axles should be used in the rear when higher ground clearance, reduced drive shaft angles or short wheelbase are desirable issues. Reverse-cut rear axles should be avoided for heavy GVW vehicles or heavy highway towing.

The gear sets used in each type of axle are not interchangeable: Standard cut gears cannot be used in place of reverse cut, and vice versa. The housings, which have different lubrication passages, are also not interchangeable. However, differential cases (open, l/s, or locker) are compatible with both styles, as long as case spline count matches the axle shaft.

Есть вопросы? Спросить на WhatsappСпросить на WhatsApp

     по E-mail: показать форму и задать вопрос

Каталог